|
Vicmarc Chuck Jaws |
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|
Dovetail Jaws Dovetail
jaws are designed for mounting bowls by expanding into a recess or clamping
onto a spigot. The size indicated is the outside measurement of the jaw face
when fully closed. Dovetail jaws provide approximately 25mm of expansion
beyond their specified size.
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|
Step Jaws Step
Jaws, designed by the famous Australian wood turner and author Richard
Raffan, and are used for holding a range of spigot sizes with minimum
jaw movement and without the necessity to change the jaws. Boxes are
easily turned using the step jaws. The bottom can be turned by holding the
rim without leaving unsightly pressure marks.
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|
Long Nose Jaws These
jaws allow better access between the chuck body and the rear of the work
piece. They are also very practical when pre- turned work pieces or long
work pieces have to be refastened. For
example, when turning serviette rings or remounting rough turned work
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
***Please click on this link EMAIL to make
enquires and place orders***
|
|
Shark
jaws are so called because of their serrated inner and outer jaw surfaces.
These extended jaws provide an aggressive hold. They hold cylinder
spigots much more safely than standard jaws. They are much easier and faster
than traditional jaws used to turn long work pieces. Available in.
|
|||||||||||||||||||||||||||||||||||||||
|
|
Pin Jaws Pin
Jaws, designed by well known American Wood turner and author Dick Sing, are
used for such items as kaleidoscopes and pepper grinders, etc.
|
|||||||||||||||||||||||||||||||||||||||
|
|
Pen Jaws Pen Blank Jaw set
comes as a set of 2 and are designed to clamp pen blank squares for
drilling as shown below. These Jaws can clamp from 10mm square blanks up
to 63mm square blanks. Depending on chuck
|
|||||||||||||||||||||||||||||||||||||||
|
|
Dovetail 2 Step Jaws - 70mm The 70mm Dovetail
Jaws were designed to accommodate work that vary between the standard
Dovetail Jaws that are supplied with the Chuck and 100mm Dovetail Jaws,
available only for VM90 and VM100.
|
|||||||||||||||||||||||||||||||||||||||
***Please click on this link EMAIL to make
enquires and place orders***
|
|
Soft Jaw Would
you like to turn your own custom made Jaws to suit your work piece?? Now you
can do it with the all-new Vicmarc Acetyl Soft Jaws. Jaws are made from
Acetyl, allow Wood turners to turn their own Chuck Jaws for
whatever diameter is required to hold the work piece. Once screwed on to
a Vicmarc chuck, simply turn the Acetyl Jaws for each job required using
normal woodturning chisels. On completion of a job, machine a new clamping
shape in to the Acetyl jaws to be ready for the next job.
|
||||||||||||||||||||||||||||||||||||||||||||||||||
|
|
The adjustable jaws allow you to re- chuck bowls for finishing
the bottom or do light clean- up work on the foot of the bowl. To mount the
bowl, the bowl is reversed and held by the rim, either Internal or external,
with 8 unique soft PVC stoppers which are mounted on the face of the jaws.
|
||||||||||||||||||||||||||||||||||||||||||||||||||
|
|
Vacuum Plate This device
has been designed as an aid to woodturning. It enables an item to be
remounted on the lathe for finishing without risking further holding marks.
This device can be fitted directly into a Vicmarc chuck via the standard
jaws, or an insert can be supplied as an extra to allow mounting directly
onto the spindle. V01228 + V01217 Size: 300mm Diameter $341.00 |
||||||||||||||||||||||||||||||||||||||||||||||||||
|
|
3 in 1 Screw Face Plate This
screw chuck has three alternative diameters of 50, 75 and 100mm to give
optimum support to any size of work. Made from K1045 medium tensile steel.
Fitted with the Glaser screw. Fits most lathes. Alternative thread sizes
available by using Vicmarc chuck inserts. $148.50 direct thread price |
||||||||||||||||||||||||||||||||||||||||||||||||||
|
|
Screw Face Plate The
Screw Face Plate enables you to quickly remove the job from the Chuck and
remount if necessary. Dovetail pick up will fit any Vicmarc Chuck V00425 $57.00 |
||||||||||||||||||||||||||||||||||||||||||||||||||
|
|
Faceplate Rings These can
be used instead of the traditional faceplate. They facilitate remounting of
prepared blanks by mounting directly onto the chuck jaws. Also can be used
for turning green wood which will require returning later on. Fit
standard jaws supplied on chuck.
|
||||||||||||||||||||||||||||||||||||||||||||||||||
|
Prices Subject to change without notice |
|||||||||||||||||||||||||||||||||||||||||||||||||||
